Pressure sensor 0 - 10 Bar Absolute MEMS piezo resistive with pressure sensor ASIC signal management
TM-PS0316 Series
Pressure sensors
Description
PS0316 series are designed by a mixed package where the silicon pressure sensor and signal processing circuit are packaged into an integral pressure chip. Furthermore, PS0314 series can offer compact design, high accuracy, greatest possible operational reliability, and other numerous options.
Active temperature compensation and linear calibration ensures that the analog signal output of the chip is proportional to the supply voltage and led to a linear function to the input pressure.
Customer - specific sensor characteristics can also be defined although the model PS0314 ensures a wide range of operating pressure, while its typical supply voltage is 5±0.5 V and current is 2.0 mA.
Characteristics
◼ Solid state, High reliability
◼ Cost-effective, Compact design
◼ Active temperature compensation range
from - 40C to + 130C
◼ Patch structure design, Clear pin definition
◼ Error at 0C...110C ≦ 1%
Schematic Diagram
Applications
◼ Tire pressure monitoring, TPMS
◼ Engine control, MAP sensors
◼ Altimeter, barometer
◼ Air pressure gauge, digital pressure gauge
◼ Ship navigation system
◼ Aircraft avionic system
| Specification ( Values depend upon the prevailing operating conditions of VS = 5VDC,TA = 25C, P1 > P2 ) |
| Pressure Range | 20 KPa…30KPa…700KPa …1600KPa |
| | | Min | Typical | Max | Unit | Remarks |
| Operating Voltage ⑴ | | 4.5 | 5.0 | 5.5 | VDC | Vs |
| Operating Current | | / | 2 | 4 | mAdc | Io |
| Minimum pressure offset (0 to 85C) @Vs=5V ⑵ | | 0.355 | 0.400 | 0.445 | VDC | Voff |
| Full range output (0 to 85C) @Vs=5V ⑶ | | 4.605 | 4.650 | 4.695 | VDC | VFSO |
| Full range span (0 to 85C) @Vs=5V ⑷ | | 4.160 | 4.250 | 4.340 | VDC | VFSS |
| Accuracy (5) | | / | / | ±1.5 | %FSS | / |
| Sensitivity | | / | 18.5 | / | Mv/KPa | V/P |
| Response time (6) | | / | 1.0 | / | mS |  R |
| Pre-treatment time (7) | | / | 10 | / | mS | / |
| Offset stability (8) | | / | ±0.5 | / | %FSS | / |
| Power-up time | | / | / | 100 | mS | tpon |
Note:
1. The module output is proportional linear in the operating voltage range.
2. Minimum pressure offset: an output voltage of the module under the minimum pressure within the pressure range.
3. Full range output: an output voltage of the module under the maximum pressure within the pressure range.
4. Full range span: an algebraic difference between the output value at maximum pressure and the output value at minimum pressure
within the pressure range.
5. Accuracy includes linearity, temperature hysteresis, zero offset and end value deviation (corresponds to measured error).
6. Response time: the time required to go from 10% of the output to 90% of the theoretical value.
7. Pre-treatment time: the time to take for stability after the pressure stabilizes.
8. Offset stability: the output offset of the module after a pulse pressure and temperature cycle for 1000 hours.
Limit parameters
Maximum rating value(1)
| Parameter name | Symbol | Rating value | Unit |
| Maximum pressure | PMAX | 1600 | kPa |
| Storage temperature | TSTG | -50 to 135 | C |
| Operating temperature | TA | -40 to 125 | C |
Maximum output current (2) | IO+ | +2.0 | mAdc |
| Maximum input current (2) | IO- | -2.0 | mAdc |
Note:
1. Maximum rating value will result in parameter degradation or device damage.
2. The maximum input & output current is controlled by the impedance between the ground and the power supply in the actual circui
Typical application
Cautions in use:
Since some steps in the manufacturing process of the chip's regulating circuit are kinds of CMOS process followed by unique sensor package, a variety of high electrostatic damage should be avoid in your product process. So please pay attention to the following points:
1. Anti-static safety tables are available on site, including anti-static table mat, floor mat, and operator’s wristband;
2. Tools and equipment are grounded, for example, an anti-static soldering iron is used in manual welding process;
3. Anti-static transfer boxes are available (note: ordinary plastic and metal containers are not anti-static things);
4. The ultrasonic welding process is not recommended to implement , which would affect the chip package;
5. Do not block the inlet hole on the top when manufacturing your products.
Product Tags:
|
|
0 - 10 Bar Absolute MEMS Piezo Resistive Pressure Sensor ASIC Signal Management Images
|
